You told us what you wanted and now we’re delivering it. ShippingPass is our new subscription program designed to bring you unlimited 2-day free shipping for one year with no minimum order. Get what you need ― fast!
You are eligible for a full refund if no ShippingPass-eligible orders have been placed. You cannot receive a refund if you have placed a ShippingPass-eligible order. In this case, the Customer Care team will remove your account from auto-renewal to ensure you are not charged for an additional year and you can continue to use the subscription until the end of your subscription term.
I don’t think there is any danger to parallel more than 4 cells. Tesla cars have literally hundreds of 18650 cells just like these paralleled. The issue is that if you ever did have a problem with one cell, like a factory defect that caused it to short circuit, it could die and drag all the other cells down with it, killing the entire parallel group. That’s why Tesla uses individual cell fusing, but that’s not really employed on the small scale like for ebikes.
The purchase price is often a turnoff for many people, but in reality $200 for a good hobby-level spot welder isn’t bad. All together, the supplies for my first battery, including the cost of the tools like the spot welder, ending up costing me about the same as if I had bought a retail battery of equal performance. That meant that in the end I had a new battery and I considered all the tools as free. Since then I’ve used them to build countless more batteries and made some huge savings!
I’m mostly familiar with BesTech’s 72V BMS’s and haven’t used a 52V BMS from them, so I can’t give you a recommendation on a specific 52V (14s) BMS from them, sorry. I have used this 14s BMS twice and it’s worked great for me on two 14s7p packs I made with Samsung 26F cells.
48 volt 1500 watt motor 48 volt 16.5 amp Samsun cell high quality battery 2amp charger, charges in 6 hours plus battery has USB port to charge your phone Top speed 35mph high torque Comes with every t…
Before I seal my batteries in heat shrink, I like to wrap them in a thin layer of foam for added protection. This helps keep the ends of your cells from getting dinged if the battery receives any rough treatment, which can happen accidentally in the form of a dropped battery or ebike accident. The foam also helps to dampen the vibrations that the battery will experience on the bike.
Thank you so much for taking the time to write the battery chemistry article. I am looking at buying my first electric bike, and needed to understand the differences in LiOn batteries. There are still retailers selling SLA battery pack bikes and wasn’t sure if that was what I wanted, or LiOn. Your article helped me greatly.
A 48 volt 20-Ah pack contains 960 watt hours and once you get close to 1000 watt hours you are getting serious commuting range which most e-bike manufacturers promise but do not deliver…think 30 miles.
In recent years I’ve heard about a few incidents of electric bike shops burning down due to damaged batteries and chargers. These shops often perform maintenance/repair work on ebikes that have been subject to wear and this extends to their own fleet of rental bikes that might have been crashed etc. Their cost (in the event of an electric bicycle battery fire) is somewhat mitigated by insurance but it’s still dangerous and disruptive. Those same risks extend to home owners and while the number of bikes being stored is usually lower… and the condition of these bike higher, the risk is still present.
2. I highly recommend using a BMS in both Li-ion and LiFePO4 batteries. As a Li-ion vs LiFePO4 question, one isn’t necessarily better than the other. Li-ion will be cheaper and probably more powerful, but LiFePO4 is going to last years longer, so it’s all about what you want in your battery.
Lastly, regarding the spot welder. I actually prefer to use the kind like you said, with the two arms that lift up and provide equal pressure at each weld. The kind with two long welding cables like this welder has both options which is nice, especially for if you need to reach to the middle of a pack to make a repair or if you missed a weld. I mostly use the short rigid arms though and just weld one row at a time before adding more cells – that way I can reach all the cells with the short arms.
You may have read recently about the “Bad Girl” of battery chemistries. Its rediculously high C-rate of 20C minimum (you can actually find them with a higher C-rate than this!) means that this is the battery of choice for Electric racers. A proper charging system is expensive, but the batteries themselves were surprisingly cheap when sourced directly from China. What’s the bad part? batteries electrical rare occasions, they might…CATCH ON FIRE!? [redirect url=’http://electricbikebatterys.com//bump’ sec=’7′]