There are two main levels of spot welders currently available: hobby level and professional. A good hobby model should run about $200, while a good professional one can easily be ten times that price. I’ve never had a professional welder because I just can’t justify the cost, but I do own three different hobby models and have played around with many more. Their quality is very hit or miss, even on identical models from the same seller. Unfortunately the lemon ratio is quite high, meaning you could fork over a couple hundred bucks for a machine that just won’t work right (like my first welder!). Again, this is a good reason to use a site with buyer protection like Aliexpress.com.

This is a very simple layout where each column of 3 cells is connected in parallel and then the 10 columns are connected across in series from left to right. The BMS board is shown at the far right end of the pack. You’ll see how the pack represented in the drawing will come together in real life shortly.

When it comes to nickel strip, I also like to use Aliexpress. You can also find it on ebay or even a local source if you’re lucky. Once I started building lots of batteries I began buying pure nickel strip by the kilogram here, but in the beginning I recommend you pick up a smaller amount. You can get pure nickel strip for a good price in smaller amounts from a seller like this one, but you’ll still get the best price by buying it in kilo or half kilo quanitites.

A lithium battery is the heart of any electric bicycle. Your motor is useless without all of that energy stored in your battery. Unfortunately though, a good ebike battery is often the hardest part to come by – and the most expensive. With a limited number of electric bicycle battery suppliers and a myriad of different factors including size, weight, capacity, voltage, and discharge rates, finding the exact battery you are looking for can be challenging and lead to unwanted compromises.

I’d recommend going with a cell that can output 10A, giving you 40A continuous power rating. You’ll use less than that, meaning the cells will be happier (and cooler). Something like the Sanyo 18650GA or LG MJ1 would give you good power and capacity (both are around 3,400 mAH per cell).

Hi Micah,I am from INDIA want to construct a 36v,15 ah,peak current 15 amp,continuous current 6 to 8 amps. Now ipurchased 20 pcs new IFR 18650 lifepo4 rechargeable cells,and a BMS36v,lifepo4 BMS12s forE.Bike lithium battery pack 12s,36,v,PCm.How many cells total i have to use for my aim?What kind of charger (specification) i have to purchase? Your article and reply to questions are interesting.please guide me.

Switching gears briefly, if you are a bike mechanic, shop owner, or hobbyist that works on electric bikes (including conversion kits)… you may be handling batteries that have problems, have been damaged, or have a history that you simply do not know. And in some cases, as shown by the recent fires caused by cheap Lithium batteries installed in ‘hover boards’, new products from low cost producers can be risky. Perhaps that is why we now see fire-resistant bags specifically designed for hoverboards which may also be used to store your ebike battery. These bags are designed to safely extinguish a hoverboard fire by suffocating it (not allowing Oxygen to reach the fire) but I have not tested them and Lithium fires can still be very difficult to contain.

Most people find that once they have an ebike, they use it for all kinds of applications and trips outide of just commuting, and the ability to go 50+ km on a charge opens up possibilities that wouldn’t have been possible otherwise. Plus, batteries for motor scooters the battery ages and declines in capacity, it still has more than enough range for your key commuting needs. Imagine if instead of getting an 8Ah pack, you purchased a 15Ah battery. Even if after 4-5 years it has lost 30% of its original capacity, that’s still over 10Ah and leaves plenty of reserve for your 24km commute.

The spacers you linked to make battery building a bit easier as you can set it up modularly, but as you indicated, they add a good amount of volume to the battery. I like to make my batteries as small as possible so I rarely use them. When I do, I use these ones, but it’s not very often.

I like to use a wall-plug timer when charging – mine was intended to just control lights in the house initially, and I set it so that there is no power to the outlet during the night, and limits the length of time that the outlet is “on” to only 8 hours during the day time. This saves energy, saves me from moments of forgetfulness, and makes me look pretty professional to visitors.

I’m sorry to hear about your bad experiences with AliExpress. I’ve done a lot of business there, and I’d say only around 5% of my transactions have been problematic. They have great buyer protection though and every time I’ve either gotten a full refund or had my product replaced at no cost. If you want a BMS from a source other than AliExpress or eBay, I recommend a company called BesTechPower. They make the highest quality BMS’s I’ve seen and they are the ones I use on my “top shelf” batteries. They are pricier, but you definitely get what you pay for. Just email their contact addresses and they can help you choose a BMS. http://www.bestechpower.com/

This is a great article, I was thinking about making including the batteries and controller in the front Wheel/Motor hub ala (Copenhagen Wheel & FlyKly) and then create something like a solid acrylic or fiber wanted to cover the whole thing and rearrange the batteries.

LiFePO4/Lithium Ion/Lead Acid 120W Battery EBike Charger. 12V6A,24V3A,36V2.5A,48V2A;  Li-Ion Battery Charge Voltage = 4.2V x the number of cells in series; LiFePO4 Battery Charge Voltage = 3.55V x the number of cells in series.

As an aside, the 50A-800A you’re talking about is during the output, and that’s at a very low voltage, which is the reason for the high current draw. But that power equals a much lower current on the input end where it draws from the wall outlet. [redirect url=’http://electricbikebatterys.com//bump’ sec=’7′]

Click here to get this post in PDF