Lead acid batteries are the least expensive and heaviest battery option. They have a short cycle life if used regularly in deep discharge applications. For electric bikes, the most common setups use 12V bricks of either 7Ah or the larger 12Ah capacities, series connected to form 36V or 48V packs. Because of the Peukert effect, the 7Ah gel cell usually delivers about 4 amp-hours of actual capacity, while the 12Ah lead acid packs will deliver approximately 8 amp-hours. So keep this in mind when comparing a lead acid pack to one of the NiCd, NiMH, or lithium replacements. We do not offer lead acid batteries or chargers, but they are not hard to find.

Different batteries have different amperage capacities. Most cheap lithium batteries are not capable of putting out much amperage. If you have a 48 volt bike that performs well when using 25 amps, you are going to want a 48 volt battery that has close to a 20-Amp-hours or more.  If you want to eventually hot rod your ebike (read our hot rod hub motor primer here), you may want to  invest now in a high amperage battery. This will “future proof” your system by paying a little bit more now for the battery, but then you can program more performance from the controller in the future, if you want…

Also changing the fuse to a higher one could cause the wires to start a fire and the whole house would burn down if the wires are not thick enough. Also in sweden a fuse gets bigger as they are rated higher so you can fit a 20A fuse in a 10A slot, for safety.

1. Eligibility: Sweepstakes (the “Sweepstakes”) is open only to those who sign up at the online sweepstakes page and who are at least 18+ years old at the time of entry. The sweepstakes is open to the legal residents of the Contiguous USA and Canada and is void where prohibited by law. Employees of Electric Bike Technologies LLC (the “Sponsor”) their respective affiliates, subsidiaries, advertising and promotion agencies, suppliers and their immediate family members and/or those living in the same household of each are not eligible to participate in the Sweepstakes. The Sweepstakes is subject to all applicable federal, state and local laws and regulations. Void where prohibited.

You’ll see two dots where the weld was performed. Test the weld by pulling on the nickel strip (if it’s your first time using the welder). If it doesn’t come off with hand pressure, or requires a lot of strength, then it’s a good weld. If you can easily peel it off, turn the current up. If the surface looks burnt or is overly hot to the touch, turn the current down. It helps to have a spare cell or two for dialing in the power of your machine.

Once I’ve got all the cells I need checked out and ensured they have matching voltages, I like to arrange them on my work surface in the orientation of the intended pack. This gives me one final check to make sure the orientation will work as planned, and a chance to see the real-life size of the pack, minus a little bit of padding and heat shrink wrap.

The chain is a very important bicycle part. It is responsible for turning the wheel when a cyclist pedals the bike. Problems with the chain create major riding problems. Chains commonly get dry or rusty,…

Common lithium cobalt oxide (LiCoO2) batteries can catch fire or explode during loading and even when just stored. The safety depends on user precautions and the quality of the Battery Management System (BMS).

You’ve done your math correctly, though that “1000W” figure is largely arbitrary, and probably not the exact power level of the kit. Most 1000W kits I’ve seen use controllers in the 20-25A range, but it can vary greatly.

For this tutorial, I’ll be using the green Panasonic 18650PF cells shown above. Lately though I’ve been using 18650GA cells like these, which are a little bit more energy dense, meaning more battery in less space.

As an aside, the 50A-800A you’re talking about is during the output, and that’s at a very low voltage, which is the reason for the high current draw. But that power equals a much lower current on the input end where it draws from the wall outlet.

LiPo’s are the smallest, cheapest, lightest and most powerful lithium batteries. Their disadvantages include short lifespan and propensity to combust into giant fireballs if not cared for correctly (I’m not kidding, check out the short video clip below).

Used PL-350 electric bike kit, The battery does not charge. Charger is fine but only shows a red light. It sat dead for about a year. Then the controller showed about 80% after charging. Everything wo…

One question regarding the specific battery BMS you used in this build: It uses a different wire for charging vs discharging the battery. Does this mean that the regenerative braking feature cannot be used for this battery?

You told us what you wanted and now we’re delivering it. ShippingPass is our new subscription program designed to bring you unlimited 2-day free shipping for one year with no minimum order. Get what you need ― fast!

Thanks so much for all this great informating, Im going to purchase the ebook for sure! One small question first, though. I’m building a 13s8p 18650 pack from laptop batteries for my bfang 750w 25A pedicab. I already have 45V 15 Ah LiPo setups from china, but want to up my Ah.

When you buy your battery, make sure you know what its maximum amp output is. Remember, by multiplying amps and voltage you get the actual current capacity of the battery. For example a 48-volt 25 amp pack can put out 1200 watts.

At the same time though, think about if that is what you want. It could be that those cells died because of a malfunctioning BMS unit or old wiring. Putting new cells in their spots could just wind up killing those new cells in a few days or weeks. I’ve seen that happen as well. So make sure you check everything and consider all of your options!

1. The extra amperage that the battery could output isn’t wasted, it’s just sort of a safety factor. It means you aren’t stressing the battery to its limit. Also, batteries only get their full rated capacity at lower discharged. So you’re more likely to get the full capacity now than if you actually pulled 50A out of it.

Most people find that once they have an ebike, they use it for all kinds of applications and trips outide of just commuting, and the ability to go 50+ km on a charge opens up possibilities that wouldn’t have been possible otherwise. Plus, as the battery ages and declines in capacity, it still has more than enough range for your key commuting needs. Imagine if instead of getting an 8Ah pack, you purchased a 15Ah battery. Even if after 4-5 years it has lost 30% of its original capacity, that’s still over 10Ah https://en.wikipedia.org/wiki/Electric_bicycle leaves plenty of reserve for your 24km commute.

You’ll need someway to hold your cells in a straight line while welding, as free-handing is harder than it looks. I have a nice jig (that I received as a free ‘gift’ with the purchase of one of my welders) for holding my cells in a straight line while welding. However, before I received it I used a simple wooden jig I made to hold the cells while I hot glued them into a straight line.

We also maintain stock of replacement vertical seattube batteries that have been in use in the eZee bicycle line since time immemorial. If you have an eZee bike circa 2008-2012 with the Phylion lithium battery pack, you’ll be in for a serious upgrade with over twice the capacity in the same size and weight. [redirect url=’http://electricbikebatterys.com//bump’ sec=’7′]

Click here to get this post in PDF