– BMS/Greenbikekit are now selling cased or shrinkwrap LiFePo batteries based on high capacity cylindrical cells probably from Headway and with a BMS. These have a higher C Rating between 5C and 10C. This makes a 48v-10AHr battery useable in a high performance kit with 30-40A max. Using this with a 1000W-1500W motor/controller should work fine. This is heavier than LiPo but close to the holy grail. Long lasting, safe/easy/convenient, high power.

Thanks! I’m putting together a new rig I need to tow a 50lb trailer over some soft sand…I’m realizing the proper system is paramount. Any recommendations for power/battery/controllers? DIY eBikes website?

For example, suppose you see a 24V 4Ah NiMH battery pack on ebay, that is rated for 1C continuous and 2C max for short times. You might want to get two of these to make a 48V 4Ah battery for your ebike. You calculate that the range will be more than adequate for your short commute to work and back. The problem is that 1C is just 4 amps, while your ebike will probably draw 10-20 amps. If these cells are subject to such discharge rates, then the voltage will sag considerably, leading to slower performance, and the cycle life of the packs will be greatly reduced.

Excellent, excellent, excellent (did I mention excellent) motor! So much fun, so much torque. I bought mine with 30q 52v battery, unbelievable power. Done about 300 km yet but absolutely no regrets. Get the 42 teeth Lekkie ring, makes worlds of difference. The new color display is also …

I just have a simple question: I would like to replace the Nicad battery 24V / 5Ah of my old Yamaha PAS XPC26 with a 7s3p and maybe try a 8s3p for something more “punchy” (hoping the controller will not burn …) . Do you think I can buy a 10s BMS and use it with a 7s or 8s battery? In this case, what should I do with the spare balance wires ?

One question regarding the specific battery BMS you used in this build: It uses a different wire for charging vs discharging the battery. Does this mean that the regenerative braking feature cannot be used for this battery?

Landcrossers Fish E-Bike Battery. Case Material: ABS Aluminium alloy. Fuse Installation position: Inside on the PCB. Component: Li(NiCoMn)O2. Parts included: 1 x Lithium Battery with Aluminum case(Bas…

The ShippingPass assortment is continually being optimized. Products are added and removed for lots of reasons, but the main reason is to show items that we’re 100% sure we can deliver within the promised timeline.

A better and simpler solution would be, as you said, to carry a second battery and just swap the connector from the old battery to the new one when the old battery is depleted. There are a few types of bottle batteries out there, I recommend googling “bottle battery” if you haven’t yet, you’ll likely find a few options. I don’t know if this is the same model as yours, but some common styles similar to your description can be found here and here.

A123 is a brand name of lithium ion phosphate battery used in many EV even full car applications.. A123 cells are known to be of high quality and capable of having high-amp discharge rates with long life expectancy of over 1000 charges. They can provide large amounts of power batteries electrical have been used in racing applications as well as electric car builds. Chrysler has chosen to use A123 cells in their electric cars.

Here is a an example of a large format soft pouch LiPo pack with 13 cells, and a BMS. This pack was built using cobalt LiPo soft cells with a BMS from a Chinese factory for an electric bike. You can see the top cell has been squished, causing the cell to fail and the BMS to shut down the battery, and not allowing it to charge or discharge. This pack is small and light (7lbs).  This $500 pack is now ruined, but  all is not lost since it did not start a fire, and it did NOT take the house with it.

Finally, have you used the type of spot welder shown with hand held probes? Can see the benefit of greater reach, but do you know if this gives as neat a result (my spot welder there is a very firm press up to activate, hence the discharge only occurs when the tips of the welder are pressing the strip firmly against the top of the cell so i assume ensuring a tight weld)

Short for bicycle motocross, BMX is a type of bike designed for dirt, street, flatland, and park rides. This is a more casual form of cycling, which riders enjoy for both pleasure and sport. BMX riding… [redirect url=’http://electricbikebatterys.com//bump’ sec=’7′]