Hey Brian, good question. You can actually do regenerative braking this way, the only problem is that you won’t be using the balancing circuit part of the BMS as it will charge straight back through the discharge circuit. Theoretically this is fine, with the exception of one specific case where this could be a problem. If you charged your battery at the top of a huge hill and then immediately rolled down that hill for a long time while using regenerative braking, you could actually overcharge the battery. That scenario is pretty rare though.

BMS (Battery Management System) watch pictures for all technical information. BMS / PCM (reference)16S-40A. Best upgrade Lithium Battery in most compact size (270 ±2) (150 ±2) (90 ±2 ) mm that will fi…

Please forward to every member of ur family of em3ev! Here it’s been a great ride! Tks guys for everything. I can do mtb again bcause of your kit. My lower back and my knee been injured badly and i got fibromyalgia so without ur help my bike …

BesTechPower makes some of the best BMS’s in the industry. You pay for that quality, but I believe it is well worth it. I haven’t used that specific BMS you linked to, so I can’t give you specific feedback on it. I haven’t done very many 7s packs, as that’s on the lower end for ebike use. The few I’ve done had some cheaper BMS’s and not the two wire design I mentioned. Sorry I don’t have any specific recommendations for you – it’s just a lower voltage level that I don’t often use.

Spot welders for batteries aren’t the same as most home spot welders. Unlike the large jaw spot welders for home workshops, battery spot welders have the electrodes on the same side. I’ve never seen them for sale in the US, but they can be found pretty easily on eBay and other international commerce websites. My full time use welder is a fairly simple model that I got here. A highly recommended source for a slightly nicer spot welder design (pictured below) with both mounted and handheld electrodes can be found here.

[74V, 89V, and 104V @ 13Ah are available by connecting 2 batteries below in series.  37V 26Ah and 52V 26Ah are available by connecting 2 batteries below in parallel.  Instructions provided upon request.]

Shenzhen Tianlihe Technology Co.,Ltd as a lithium ion battery pack factory was founded in 2005, which is specialized in the R&D and Production of Custom lithium ion battery pack solutions, Electric bike battery and Storage lithium ion battery. TLH BATTERY is certified by the ISO9001:2008 certificate, occupying area of 2,000 square meters with advanced production equipment and high efficient management system.

This is our smallest battery offering specifically aimed at people who have to travel or fly with their ebike. Each module is 36V 2.7Ah, so just under 100 watt-hours, exempting it from most of the heavy shipping restrictions. You can parallel connect them for as much capacity as required, and series connect them for 72V setups. Designed and made in Canada by Grin Tech, full details here.

LiMn was by far the most common chemistry in cheap (and expensive!) built up electric bikes for a long time. It’s a cheap, light, safe chemistry. The problem is low C, but much more importantly short life. And not just a short number of cycles but a short shelf life as well. Losing 20% capacity a year even if you don’t use the battery much leads to a lot of expense and warranty claims. LiNiCoMn has the same low cycle life, light and cheap characteristics, but it seems to have a longer shelf life and a slightly higher C.

The answer is that, unless you are seriously budget or weight constrained, this would probably be a bad battery investment. It might fit the bill initially for your commuting needs, but then it doesn’t really leave any reserve if you need to run some errands on the way home, or forget to charge it up one night etc. Even worse, as the battery ages over time the capacity drops. After a year your 8Ah battery is now only 7Ah, it’s only barely able to do your daily commute, and the next year when it is just 6Ah you now need to carry the charger with you and top it up at work every day.

Hi Grant! I think that depends on any accessories that the battery charger may offer. I think you’d be better off getting an inverter to connect to your car battery which can output 120 Volt AC. Look for a pure sine wave inverter… here’s a guide that may help. I used it to install an inverter in my own car 🙂

You want to be really sure you get this part right, and if you aren’t certain, I’d recommend having an electrician or the company help you. But you can determine positive and negative on the charge port by using a digital multimeter on the DC voltage setting. Probe between the three pins on your bike’s charging port to find which pins give you a positive readout of between 30-42V (Depending on level of charge). When you find it, the positive pin will be on the red probe and the negative pin on the black probe. Be careful not to short the pins together or touch the probes together, those XLR connectors are cramped quarters. And again, make sure you’re certain you’ve got it right – connecting something backwards could damage your bike’s battery.

I finally made it happen on BMS #3 (the unfortunate thing about AliExpress is that every dumb mistake that kills a part is another month added to the project) and the battery seems to work great, though it only has a couple miles so far.

Thanks for the info! I have read about builders that used Sony Konion LiMn cells that were removed from Makita Drill packs. The constant theme of their reports show that the thing they seem to like the most, is that the cells seem to just stay in balance. So much so that, several have built packs with no BMS. If there is a measurable LiMn shelf life issue compared to other chemistries, it doesn’t seem to bother the DIY pack building crowd.

Electric bikes are a reliable source of transportation. With a new battery from Batteries Plus Bulbs, you can expect the same level of reliability. Our high capacity, replacement batteries will get your scooter moving again and keep it running for a long time.

2. Agreement to Rules: By participating, you agree to be fully unconditionally bound by these Rules, and you represent and warrant that you meet the eligibility requirements set forth herein. In addition, you agree to http://huntneqip.com the decisions of Electric Bike Technologies LLC, as final and binding as it relates to the content. The Sweepstakes is subject to all applicable federal, state and local laws.

The high C-rate is not the only reason LiPo is adored by the high performance crowd, the addition of Cobalt to the cathode meant that more power would fit in a smaller package. This was driven by the boom in Radio-Controlled (RC) models in the late 1990’s (RC airplanes, cars, helicopters, etc). When that market suddenly expanded, an Australian enthusiast started a company to supply RC parts from factories in China. Hobby King.com was born. Last year, due to popular demand, HK has opened warehouses in The USA and in Germany (edit: even more countries have HK warehouses now).

I’m glad you enjoyed the article. To answer your questions: I chose this type of battery instead of LiFePO4 mostly because of the cost and convenience. LiFePO4 is a bit more expensive and has fewer options for cells. These Li-ion cells are a bit less expensive and there are dozens of options with many different specifications for any power/capacity need. I’ve used and built LiFePO4 packs before and they have their own unique advantages, but for me they just don’t add up to enough.

When choosing a battery for your bike, not only is the weight important but the volume is also important. You want your pack as small as possible so its easy to stow and easy to hide. So therefore you should consider you battery’s volume, not just its weight. For sure you need to go with a lithium chemistry and not an old school heavy and large Sealed Lead Acid (SLA) or Nickel-Metal Hydride (NiMH) chemistry. [redirect url=’http://electricbikebatterys.com//bump’ sec=’7′]