Landcrossers Fish E-Bike Battery. Case Material: ABS Aluminium alloy. Fuse Installation position: Inside on the PCB. Component: Li(NiCoMn)O2. Parts included: 1 x Lithium Battery with Aluminum case(Bas…

If you charge batteries off the bike, I suggest doing so on a metal rack that has wheels on the bottom (very inexpensive at hardware stores) whith the battery(s), and chargers on the rack. In the event of smoke, bad smell, or fire, you can shove it out the door quickly. Locate it closest to a doorway that you can use to eject the battery easily, quickly and without coming in contact with the burning material or breathing the fumes. Consider how you would get a bike out the door. I have a boat hook that could be used to drag just about anything outside, and it is ~2 meters long.

I have built a few 13s lithium batteries in the past year following your instructions. Thanks. I have taken one of the batteries apart to check its condition as it is the middle of winter here in Winnipeg, Canada. Two parallel sets were out of balance with the rest of the pack. I was wondering if there is a way to use my imax b6 balance chargers to rewire the battery and keep each parallel pack in balance for sure! This way I will bypass the bms. Does this make sense?

If you are upgrading or replacing an existing battery pack, it is always safe to replace it with a battery that has the same nominal voltage. If you have an 36V ebike setup that is not from us, and are looking to ‘upgrade’ to a 48V/52V pack, more often than not you can do this without damaging the existing electronics. That is because most 36V motor controllers use 60V rated mosfets and 63V rated capacitors, and so even a fully charged 52V battery will not exceed these values.

This step is somewhat optional. You should seal your battery somehow to prevent it from shorting on all of that exposed nickel, but it doesn’t necessarily have to be with heat shrink wrap. Some people use duct tape, plastic wrap, fabric, etc. In my opinion though, shrink wrap is the best method because it not only provides a largely water resistant (though not water-proof) seal, but also provides constant and even pressure on all of your connections and wires, reducing the risk of vibration damage.

As a side-note, the Boeing 777 Dreamliner battery fire was using LiCo. They wanted a battery that was as light as possible, and as compact as possible. I am not an engineer, but I agree with the statement made by “Tesla” electric car maker Elon Musk, when he said that there was NOT adequate heat insulation between each cell. Better individual cell insulation would prevent a bad cell that was getting hot from heating up the surrounding cells. That is what led to a domino effect. The Tesla cars have a cell cooling system, and the on-board computer can detect and cut-off any cell-group that is getting hot.

Hi Danl, that sounds like a very high power motor. Most consumer ebikes are in the 36V-48V range, so if your motor is advertised as being rated for those higher voltages then it’s definitely a more serious motor. If you’re looking for a ready-built and relatively inexpensive battery, then something like this might work for you, though I haven’t personally used that battery. You can of course build your own battery just like batteries for motor scooters did in this article, and that way you’ll be sure to get exactly what you’re looking for. The AH’s required will depend on the quality of the battery. A batter rated for higher current will require fewer AH’s than a lower quality battery. I’d aim for at least 20AH, if not more on a motor of that size. It’s going to eat your battery quickly, so you’ll want more capacity to be able to ride longer.

Yes, you can upgrade a GIO PB710 with a lithium battery. You just want to make sure your battery is the same voltage as the original lead acid battery and that it can handle the current demanded by the bike’s controller.

I am working on a similar project, and was wondering if the BMS’s that you recommended would handle any back EMF from the motor (from regenerative braking, for example.) I see that there are separate leads for charging and discharging, so I’m guessing if current flowed back through the discharge circuit that would be bad. Do you have any recommendations on a BMS (or something different) that would handle this condition?

Most of the problems occur when charging an ebike because they are unsupervised and that is when a LiPo fire can burn down a house etc. Use common sense on where you are going to charge your bike or battery pack, so that if it does burst into flames it does not take your house with you. I have a big steel barbecue grill set up in my entryway which  I charge my battery packs in  as nice safeguard.  This involved taking the battery pack out of the bike after each ride but I am OK with that:

It’s a good question. You need to use a 5s BMS. You can’t use a BMS rated for more cells because if the BMS see’s that cells are “missing” it will likely trip the protection circuit and your battery won’t provide any current. I’m not sure how easy a 5s BMS will be to find. A quick Aliexpress search shows me that something like this will probably work.

Batteries Plus Bulbs is proud to be an industry leader in battery recycling. That’s why we have an extensive recycling program to help reduce waste and environmental hazards. Stop by your local store and ask an associate what your area’s regulations are regarding e-bike batteries. If you’re having trouble finding a battery for your electric bike, visit your local Batteries Plus Bulbs store and ask an associate for help. They’ll help you find the perfect battery for your bike based on your needs and budget.

For people who are new to the hobby, ready-made lithium packs are the way to go. Several manufacturers offer ready to go Lithium packs with a built in Battery Management System (BMS) at affordable prices.

Battery Model:36V 12Ah. New Lithium 36 volt 12 amp-hour Battery for Electric Bikes (e-bikes) and Scooters. Life cycle:more than 600 cycles. Battery Size (Approximate): 8″ x 3.75″ x 2.75″. Battery Weig… [redirect url=’http://electricbikebatterys.com//bump’ sec=’7′]