Month: June 2016

“36v battery for electric bike |ebike bms”

This is truly inspiring, this has helped me out in so many ways, I have a few questions I want to ask please. I was looking to withdraw amps by making connections from the battery directly but charging it through the bms as my bms is similar to yours max withdraw of 40 but I need upto 50a. and also are most BMS self balancing ? Meaning wil they always try to balance themselves even when they are not being charged ? Hope to hear from you soon kind regards Actually, it is not recommended to use protected cells in ebike builds. There a few reasons but the main ones are 1) unreliability of the protection circuit, 2) many points of failure, and 3) lower discharge current of individual cell protection circuits. C values seem to be as much about cell packaging as chemistry for LiFePo/LiMn/LiNiCoMn Pouch and prismatic cells with high AHr per cell tend to have a C value of about 1 to 1.5. So cheap packs both cased and shrink wrapped or from suppliers like Ping seem to be like this. Cylindrical cells from A123 or Headway tend to have C values of 3C to 5C upwards. And for a fully built pack, C is as much about cells in parallel as anything. eg 10s2p having twice the C of 10s1p Again BMSBattery/GreenBikeKit are now selling...

Read More

“18650 battery pack diy electric bike batteries for sale”

Hi I need help! I am building my own battery pack from old laptop batteries (18650’s). I bought the cheep $250 48v 1000w ebike conversion kit on ebay. I have many questions! It seems the perfect number of cells to connect in series are 13! This is a big problem for me because I am cheep and I already bought the Imax B6 battery balancer charger. I also bought 7x 6s balancer leads and 5x 4s leads. The Imax has a max charge voltage of 22.2v (so it sais in the manual), and a max balance of 6 cells at once. I also bought the parallel balance charging board. I don’t want to charge two or three packs at once to just have to turn around and charge one separately. So now I’m faced with the decision of making a 12 series battery or a 15 series battery (I will buy 5s leads in this case). The problem is with the 12 series battery the nominal voltage is only 43.2. Or a 15 series battery with a nominal voltage of 54. Which I’m pretty sure is a big no no because the controller is only meant to handle 48v within reason (13s max charge voltage of 53.3 and 12s 49.2 at 4.1 v per cell). But if I make it a 12s, running around most of the trip at...

Read More

“e-bike batteries “

Offset packing results in a shorter pack because the parallel groups are offset by half a cell, taking up part of the space between the cells of the previous parallel group. However, this results in a somewhat wider pack as the offset parallel groups extend to each side by a quarter of a cell more than they would have in linear packing. Offset packing is handy for times where you need to fit the pack into a shorter area (such as the frame triangle) and don’t care about the width penalty. The Panasonic NCR18650PD cells can be purchased at Fast Tech dot Com, who reliably processed and shipped my transaction. Good prices, too, from this Chinese-based vendor. I “tested the waters” by buying just 4 cells first and will certainly be buying more from them. I’d like to make my own e-bike pack with these cells and further inquired to AllCell to see if I could obtain one of their PCM blocks. Unfortunately, they will only sell these on bulk wholesale basis to established pack-building businesses. The DIY pack builder will have to explore other options. Nickel Cadmium was the old standard for rechargeable consumer cells in the familiar AA, C, 9V series. They are known for robust characteristics, a good cycle life, and high discharge capabilities. They are still widely used in cordless power tools, R/C toys and similar...

Read More
  • 1
  • 2