Nominal capacity: 12Ah (Fully charged after 0.5C discharge to 38V capacity). Cycle life: Standard charge and fast discharge cycle 500 times, the capacity will notless than 60% of the nominal capacity.

Continue down the row of cells placing a weld on each cell. Then go back and do another set of welds on each cell. I like to do 2-3 welds (4-6 weld points) per cell. Any less and the weld isn’t as secure; any more and you’re just unnecessarily heating the cell. More and more welds won’t increase the current carrying ability of the nickel strip very much. The actual weld point isn’t the only place where current flows from the cell to the strip. A flat piece of nickel will be touching the whole surface of the cell cap, not just at the points of the weld. So 6 weld points is plenty to ensure good contact and connection.

Now I’ve got all of my pack sealed in heat shrink with my wires exiting the seam between the two layers of shrink wrap. I could have stopped here, but I didn’t particularly like the way the shrink fell on the wire exit there, from a purely aesthetic standpoint. So I actually took a third piece of shrink wrap, the same size (285 mm) as that first piece and went around the long axis of the pack one more time to pull the wires down tight to the end of the pack.

hello sir. nice guide FOR battery pack li-ion… i will try an electric bike kit for my 26″ MTB. and buy 1000w hub motor kit. i can solve my battery problem (expensive you know) with li ion pack. i have some questions,

I would prefer to go with lithium, but I have a couple of 75 volt (i think) cells from a UPS that are brand new. They are built from regular 12v (sixteen total) sealed lead units and would make the initial investment in an ebike that much more reasonable. One huge downside is that I hope to use the folding ebike in my homebuilt aircraft. As with ebikes, excess weight is to be avoided!

I wouldn’t say incompatible but us 220 uses the full phase peak to peak of both legs of the elec drop. European and others uses a half phase (I believe) where zero to peak is 220v. Have you had a chance to look into this for me as my welder and box of new 18650’s are sitting idle waiting for me to start welding. Thanks

I hope someone can recommend another spotwelder or some other kind of Technic to fuse batteries with wire (except soldering) . This has been an expensive ordeal and if not even a techlab with endless lasers cutters and cool cants get this machine even to power up, its something wrong with the machine.

A quick note: when you get into large sizes of heat shrink, the method of quoting the size often changes from referring to the diameter of the tube to referring to the flat width (or half the circumference when in a circle). This is because at these large sizes, it’s not so much a tube anymore as two flat sheets fused together, sort of like an envelope. Keep that in mind and know what size is being quoted when you buy your large diameter heat shrink tube.

It’s not impossible, but I don’t have high hopes. When a few cells die like that, they tend to kill the other cells in the same parallel group and often can kill cells in the series groups adjacent to them. You could be looking at replacing a large number of cells outside of the ones with obvious damage, and it will be hard to confirm that you’ve found all the dead cells without pulling apart most of the pack. If you’d like to try, there’s a chance you can end up saving the pack for less than the cost of replacing it, but it’s going to be an uphill battle.

I want to build a 36v ebike battery for my 36v 500w motor. What battery you recommend for me which gives the enough current and capacity. My plane is to build a battery with 40 cells 10 in s and 4 in p,

hello. I have a KTM bike-trail’s 2013 model. I have problems with the battery. I had the bike wheel and I bought one original ktm 26V from the company. defect occurs so: I put the plug on the charger to charge the battery and flashing green LED lights and red and it is immediately interrupted – interrupted flashing red and the buzzer sounds and noises that can fix … ? Please help me if you know how. sorry for my English but I used google translator

I’ve gotten so many different BMS’s from so many different suppliers so I’m not 100% positive, but I believe it was from this source: http://www.aliexpress.com/item/NEW-Battery-Protection-BMS-PCB-Board-for-10-Packs-36V-Li-ion-Cell-max-30A-w/32291193643.html

There are many different types of lithium ebike batteries to choose from. I’ll give a short summary of the different types of electric bicycle specific lithium batteries here, but you can get a more detailed description as well as the pros and cons of each type of lithium battery in my article Not All Lithium Batteries Were Created Equal.

As with any battery, you can get longer lifetime if you keep the power under the designated amp rating, avoid completely discharging the battery, and always fully charge whenever you can. Fortunately these batteries are rated for very high amps, so this means you mainly can focus on depth of discharge for long lifetime.  These LiNMC cells are “deep cycle” meaning that they have the ability to be fully charged and discharged. However the life of the battery will significantly increase if the depth of each discharge is limited to 80% of the rated capacity.

Here is a an example of a large format soft pouch LiPo pack with 13 cells, and a BMS. This pack was built using cobalt LiPo soft cells with a BMS from a Chinese factory for an electric bike. You can see the top cell has been squished, causing the cell to fail and the BMS to shut down the battery, and not allowing it to charge or discharge. This pack is small and light (7lbs).  This $500 pack is now ruined, but  all is not lost since it did not start a fire, and it did NOT take the house with it.

Historically, the process of regenerating electricity has created a slight vibration that has loosened spokes and vastly increased maintenance costs. (At $.005 of regenerated energy per battery charge it will take some time to pay off a $35 wheel retensioning)

This is the old technology for e-bikes that is heavy as bricks and does not have longevity. Lead acid will double the weight of your https://en.wikipedia.org/wiki/Electric_bikes bike. Unless you have to because of money restraints, we advise to steer way clear of lead acid batteries.  Your bike will have a completely different feel and range if you spend the money on one of the new lithium technologies. [redirect url=’http://electricbikebatterys.com//bump’ sec=’7′]